Changes between Version 60 and Version 61 of Docs/User/FullUpdate/VersionHistory

Timestamp:

04/18/18 15:37:05 (7 years ago)

Author:

Don Wilson

Comment:

--

Docs/User/FullUpdate/VersionHistory

@@ -51 +51 @@
 [http://tech.825spectrum.com/raw-attachment/wiki/Docs/User/FullUpdate/VersionHistory/os825_01_12_009.zip OS: 01.12.009 Loader: 1.09.004 MB: 1.20.003]
  * '''OS -''' Updates to ID storage for NTEP. Updated flash update program so that "Proceed (Y/N)?" allows upper or lower case "Y" to confirm.
- * '''MnBd -''' Resolved issue that with OIML enabled and using ICAN COM3 OIML weight output was not working.
+ * '''!MnBd -''' Resolved issue that with OIML enabled and using ICAN COM3 OIML weight output was not working.
 
 === Update Pack 01.12.008 2012-07-23 ===
@@ -61 +61 @@
  * '''Loader -''' Updated to display verisons in xx.yy.zzz format where xx is metrologically significant change. Updated to set OPI CTS to receive mode to correspond to main board update to use RTS/CTS to signal start of message. Improved ICAN diagnostics - Will display message to check cable and power when CAN bus error occurs. 
  * '''OS -''' Updated to be based on uClinux OS version 2.6.29. This allows for CIFS network mounting to Windows shares. Telnet is now available. Mnbdcomm communication driver is improved to use raw non maskable interrupts for UART and DMA transfers. This prevents problem with UART overruns causing CRC errors. Also uses RTS/CTS signal from main board when multi drop mode is disabled. Configuration apps and standard indicator apps now run out of NOR flash for greater security. Appmenu display is changed to show icons and allow for signed dealer apps to show name of dealer that wrote the app as required for OIML.
- * '''MnBd -''' Updated to raise OPI CTS to during first character transmission of message to OPI board when multi drop mode is disabled. Updated OPI will use this to verify message synchronization when multi drop mode is disabled. Disabling multi drop mode seems to prevent problem with MCF5213 UART sometimes going into non-recoverable repeating transmission of data. Updated scale step mode to allow for digital output to be turned off when slow fill is finished. 
+ * '''!MnBd -''' Updated to raise OPI CTS to during first character transmission of message to OPI board when multi drop mode is disabled. Updated OPI will use this to verify message synchronization when multi drop mode is disabled. Disabling multi drop mode seems to prevent problem with MCF5213 UART sometimes going into non-recoverable repeating transmission of data. Updated scale step mode to allow for digital output to be turned off when slow fill is finished. 
 
 === Update Pack 2011-10-18 ===
@@ -90 +90 @@
  * '''OS -''' Fixed problem with usb keyboard driver that if key is held down when key repeat starts indicator may crash.
  * '''Loader -''' Improved ICAN setup to display a message when the NOVRAM is cleared and after a time delay go back to setup menu. This eliminates problem of the cell assignment display showing wrong number of cells if you do not ESCAPE out and go back in.
- * '''MnBd -''' Improved COM3 to allow TX enable/disable for RS485. Uses same command from main board as SetRTS.
+ * '''!MnBd -''' Improved COM3 to allow TX enable/disable for RS485. Uses same command from main board as SetRTS.
 
 === Update Pack 2010-08-18 ===
@@ -111 +111 @@
  * '''OS -''' Improved mndb-comm driver. Added support for ICAN and DAC cards. Added queuing to help prevent apps from overrunning buffer and causing communications problems if requests are sent to main board with insufficient delay between requests. Added prompt on startup to allow updating indicator from USB.
  * '''Loader -''' Added ICAN and DAC support. Fixed problem with 12 hour mode time may show as 0:00 instead of 12:00. Improved totalizer calibration parameter prompting to allow one set of inputs to configure all scales in totalizer.
- * '''MnBd -''' Added support for ICAN cards.
+ * '''!MnBd -''' Added support for ICAN cards.